Total
12209 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-26586 | 2 Linux, Redhat | 7 Linux Kernel, Enterprise Linux, Rhel Aus and 4 more | 2024-12-19 | 6.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_acl_tcam: Fix stack corruption When tc filters are first added to a net device, the corresponding local port gets bound to an ACL group in the device. The group contains a list of ACLs. In turn, each ACL points to a different TCAM region where the filters are stored. During forwarding, the ACLs are sequentially evaluated until a match is found. One reason to place filters in different regions is when they are added with decreasing priorities and in an alternating order so that two consecutive filters can never fit in the same region because of their key usage. In Spectrum-2 and newer ASICs the firmware started to report that the maximum number of ACLs in a group is more than 16, but the layout of the register that configures ACL groups (PAGT) was not updated to account for that. It is therefore possible to hit stack corruption [1] in the rare case where more than 16 ACLs in a group are required. Fix by limiting the maximum ACL group size to the minimum between what the firmware reports and the maximum ACLs that fit in the PAGT register. Add a test case to make sure the machine does not crash when this condition is hit. [1] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120 [...] dump_stack_lvl+0x36/0x50 panic+0x305/0x330 __stack_chk_fail+0x15/0x20 mlxsw_sp_acl_tcam_group_update+0x116/0x120 mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110 mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20 mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0 mlxsw_sp_acl_rule_add+0x47/0x240 mlxsw_sp_flower_replace+0x1a9/0x1d0 tc_setup_cb_add+0xdc/0x1c0 fl_hw_replace_filter+0x146/0x1f0 fl_change+0xc17/0x1360 tc_new_tfilter+0x472/0xb90 rtnetlink_rcv_msg+0x313/0x3b0 netlink_rcv_skb+0x58/0x100 netlink_unicast+0x244/0x390 netlink_sendmsg+0x1e4/0x440 ____sys_sendmsg+0x164/0x260 ___sys_sendmsg+0x9a/0xe0 __sys_sendmsg+0x7a/0xc0 do_syscall_64+0x40/0xe0 entry_SYSCALL_64_after_hwframe+0x63/0x6b | ||||
| CVE-2023-52916 | 2024-12-19 | 6.7 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: media: aspeed: Fix memory overwrite if timing is 1600x900 When capturing 1600x900, system could crash when system memory usage is tight. The way to reproduce this issue: 1. Use 1600x900 to display on host 2. Mount ISO through 'Virtual media' on OpenBMC's web 3. Run script as below on host to do sha continuously #!/bin/bash while [ [1] ]; do find /media -type f -printf '"%h/%f"\n' | xargs sha256sum done 4. Open KVM on OpenBMC's web The size of macro block captured is 8x8. Therefore, we should make sure the height of src-buf is 8 aligned to fix this issue. | ||||
| CVE-2023-52829 | 2024-12-19 | 6.2 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix possible out-of-bound write in ath12k_wmi_ext_hal_reg_caps() reg_cap.phy_id is extracted from WMI event and could be an unexpected value in case some errors happen. As a result out-of-bound write may occur to soc->hal_reg_cap. Fix it by validating reg_cap.phy_id before using it. This is found during code review. Compile tested only. | ||||
| CVE-2023-52755 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 8.4 High |
| In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix slab out of bounds write in smb_inherit_dacl() slab out-of-bounds write is caused by that offsets is bigger than pntsd allocation size. This patch add the check to validate 3 offsets using allocation size. | ||||
| CVE-2023-52577 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dccp: fix dccp_v4_err()/dccp_v6_err() again dh->dccph_x is the 9th byte (offset 8) in "struct dccp_hdr", not in the "byte 7" as Jann claimed. We need to make sure the ICMP messages are big enough, using more standard ways (no more assumptions). syzbot reported: BUG: KMSAN: uninit-value in pskb_may_pull_reason include/linux/skbuff.h:2667 [inline] BUG: KMSAN: uninit-value in pskb_may_pull include/linux/skbuff.h:2681 [inline] BUG: KMSAN: uninit-value in dccp_v6_err+0x426/0x1aa0 net/dccp/ipv6.c:94 pskb_may_pull_reason include/linux/skbuff.h:2667 [inline] pskb_may_pull include/linux/skbuff.h:2681 [inline] dccp_v6_err+0x426/0x1aa0 net/dccp/ipv6.c:94 icmpv6_notify+0x4c7/0x880 net/ipv6/icmp.c:867 icmpv6_rcv+0x19d5/0x30d0 ip6_protocol_deliver_rcu+0xda6/0x2a60 net/ipv6/ip6_input.c:438 ip6_input_finish net/ipv6/ip6_input.c:483 [inline] NF_HOOK include/linux/netfilter.h:304 [inline] ip6_input+0x15d/0x430 net/ipv6/ip6_input.c:492 ip6_mc_input+0xa7e/0xc80 net/ipv6/ip6_input.c:586 dst_input include/net/dst.h:468 [inline] ip6_rcv_finish+0x5db/0x870 net/ipv6/ip6_input.c:79 NF_HOOK include/linux/netfilter.h:304 [inline] ipv6_rcv+0xda/0x390 net/ipv6/ip6_input.c:310 __netif_receive_skb_one_core net/core/dev.c:5523 [inline] __netif_receive_skb+0x1a6/0x5a0 net/core/dev.c:5637 netif_receive_skb_internal net/core/dev.c:5723 [inline] netif_receive_skb+0x58/0x660 net/core/dev.c:5782 tun_rx_batched+0x83b/0x920 tun_get_user+0x564c/0x6940 drivers/net/tun.c:2002 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:1985 [inline] new_sync_write fs/read_write.c:491 [inline] vfs_write+0x8ef/0x15c0 fs/read_write.c:584 ksys_write+0x20f/0x4c0 fs/read_write.c:637 __do_sys_write fs/read_write.c:649 [inline] __se_sys_write fs/read_write.c:646 [inline] __x64_sys_write+0x93/0xd0 fs/read_write.c:646 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd Uninit was created at: slab_post_alloc_hook+0x12f/0xb70 mm/slab.h:767 slab_alloc_node mm/slub.c:3478 [inline] kmem_cache_alloc_node+0x577/0xa80 mm/slub.c:3523 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:559 __alloc_skb+0x318/0x740 net/core/skbuff.c:650 alloc_skb include/linux/skbuff.h:1286 [inline] alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6313 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2795 tun_alloc_skb drivers/net/tun.c:1531 [inline] tun_get_user+0x23cf/0x6940 drivers/net/tun.c:1846 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:1985 [inline] new_sync_write fs/read_write.c:491 [inline] vfs_write+0x8ef/0x15c0 fs/read_write.c:584 ksys_write+0x20f/0x4c0 fs/read_write.c:637 __do_sys_write fs/read_write.c:649 [inline] __se_sys_write fs/read_write.c:646 [inline] __x64_sys_write+0x93/0xd0 fs/read_write.c:646 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd CPU: 0 PID: 4995 Comm: syz-executor153 Not tainted 6.6.0-rc1-syzkaller-00014-ga747acc0b752 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/04/2023 | ||||
| CVE-2023-52531 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: Fix a memory corruption issue A few lines above, space is kzalloc()'ed for: sizeof(struct iwl_nvm_data) + sizeof(struct ieee80211_channel) + sizeof(struct ieee80211_rate) 'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine. At the end of this structure, there is the 'channels' flex array. Each element is of type 'struct ieee80211_channel'. So only 1 element is allocated in this array. When doing: mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels; We point at the first element of the 'channels' flex array. So this is fine. However, when doing: mvm->nvm_data->bands[0].bitrates = (void *)((u8 *)mvm->nvm_data->channels + 1); because of the "(u8 *)" cast, we add only 1 to the address of the beginning of the flex array. It is likely that we want point at the 'struct ieee80211_rate' allocated just after. Remove the spurious casting so that the pointer arithmetic works as expected. | ||||
| CVE-2022-48998 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: powerpc/bpf/32: Fix Oops on tail call tests test_bpf tail call tests end up as: test_bpf: #0 Tail call leaf jited:1 85 PASS test_bpf: #1 Tail call 2 jited:1 111 PASS test_bpf: #2 Tail call 3 jited:1 145 PASS test_bpf: #3 Tail call 4 jited:1 170 PASS test_bpf: #4 Tail call load/store leaf jited:1 190 PASS test_bpf: #5 Tail call load/store jited:1 BUG: Unable to handle kernel data access on write at 0xf1b4e000 Faulting instruction address: 0xbe86b710 Oops: Kernel access of bad area, sig: 11 [#1] BE PAGE_SIZE=4K MMU=Hash PowerMac Modules linked in: test_bpf(+) CPU: 0 PID: 97 Comm: insmod Not tainted 6.1.0-rc4+ #195 Hardware name: PowerMac3,1 750CL 0x87210 PowerMac NIP: be86b710 LR: be857e88 CTR: be86b704 REGS: f1b4df20 TRAP: 0300 Not tainted (6.1.0-rc4+) MSR: 00009032 <EE,ME,IR,DR,RI> CR: 28008242 XER: 00000000 DAR: f1b4e000 DSISR: 42000000 GPR00: 00000001 f1b4dfe0 c11d2280 00000000 00000000 00000000 00000002 00000000 GPR08: f1b4e000 be86b704 f1b4e000 00000000 00000000 100d816a f2440000 fe73baa8 GPR16: f2458000 00000000 c1941ae4 f1fe2248 00000045 c0de0000 f2458030 00000000 GPR24: 000003e8 0000000f f2458000 f1b4dc90 3e584b46 00000000 f24466a0 c1941a00 NIP [be86b710] 0xbe86b710 LR [be857e88] __run_one+0xec/0x264 [test_bpf] Call Trace: [f1b4dfe0] [00000002] 0x2 (unreliable) Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX ---[ end trace 0000000000000000 ]--- This is a tentative to write above the stack. The problem is encoutered with tests added by commit 38608ee7b690 ("bpf, tests: Add load store test case for tail call") This happens because tail call is done to a BPF prog with a different stack_depth. At the time being, the stack is kept as is when the caller tail calls its callee. But at exit, the callee restores the stack based on its own properties. Therefore here, at each run, r1 is erroneously increased by 32 - 16 = 16 bytes. This was done that way in order to pass the tail call count from caller to callee through the stack. As powerpc32 doesn't have a red zone in the stack, it was necessary the maintain the stack as is for the tail call. But it was not anticipated that the BPF frame size could be different. Let's take a new approach. Use register r4 to carry the tail call count during the tail call, and save it into the stack at function entry if required. This means the input parameter must be in r3, which is more correct as it is a 32 bits parameter, then tail call better match with normal BPF function entry, the down side being that we move that input parameter back and forth between r3 and r4. That can be optimised later. Doing that also has the advantage of maximising the common parts between tail calls and a normal function exit. With the fix, tail call tests are now successfull: test_bpf: #0 Tail call leaf jited:1 53 PASS test_bpf: #1 Tail call 2 jited:1 115 PASS test_bpf: #2 Tail call 3 jited:1 154 PASS test_bpf: #3 Tail call 4 jited:1 165 PASS test_bpf: #4 Tail call load/store leaf jited:1 101 PASS test_bpf: #5 Tail call load/store jited:1 141 PASS test_bpf: #6 Tail call error path, max count reached jited:1 994 PASS test_bpf: #7 Tail call count preserved across function calls jited:1 140975 PASS test_bpf: #8 Tail call error path, NULL target jited:1 110 PASS test_bpf: #9 Tail call error path, index out of range jited:1 69 PASS test_bpf: test_tail_calls: Summary: 10 PASSED, 0 FAILED, [10/10 JIT'ed] | ||||
| CVE-2022-48980 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing() The SJA1105 family has 45 L2 policing table entries (SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110 (SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but accounting for the difference in port count (5 in SJA1105 vs 10 in SJA1110) does not fully explain the difference. Rather, the SJA1110 also has L2 ingress policers for multicast traffic. If a packet is classified as multicast, it will be processed by the policer index 99 + SRCPORT. The sja1105_init_l2_policing() function initializes all L2 policers such that they don't interfere with normal packet reception by default. To have a common code between SJA1105 and SJA1110, the index of the multicast policer for the port is calculated because it's an index that is out of bounds for SJA1105 but in bounds for SJA1110, and a bounds check is performed. The code fails to do the proper thing when determining what to do with the multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast" index will be equal to 45, which is also equal to table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes through the check. But at the same time, SJA1105 doesn't have multicast policers. So the code programs the SHARINDX field of an out-of-bounds element in the L2 Policing table of the static config. The comparison between index 45 and 45 entries should have determined the code to not access this policer index on SJA1105, since its memory wasn't even allocated. With enough bad luck, the out-of-bounds write could even overwrite other valid kernel data, but in this case, the issue was detected using KASAN. Kernel log: sja1105 spi5.0: Probed switch chip: SJA1105Q ================================================================== BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340 Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8 ... Workqueue: events_unbound deferred_probe_work_func Call trace: ... sja1105_setup+0x1cbc/0x2340 dsa_register_switch+0x1284/0x18d0 sja1105_probe+0x748/0x840 ... Allocated by task 8: ... sja1105_setup+0x1bcc/0x2340 dsa_register_switch+0x1284/0x18d0 sja1105_probe+0x748/0x840 ... | ||||
| CVE-2022-48951 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx() The bounds checks in snd_soc_put_volsw_sx() are only being applied to the first channel, meaning it is possible to write out of bounds values to the second channel in stereo controls. Add appropriate checks. | ||||
| CVE-2022-48927 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: iio: adc: tsc2046: fix memory corruption by preventing array overflow On one side we have indio_dev->num_channels includes all physical channels + timestamp channel. On other side we have an array allocated only for physical channels. So, fix memory corruption by ARRAY_SIZE() instead of num_channels variable. Note the first case is a cleanup rather than a fix as the software timestamp channel bit in active_scanmask is never set by the IIO core. | ||||
| CVE-2022-48923 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: prevent copying too big compressed lzo segment Compressed length can be corrupted to be a lot larger than memory we have allocated for buffer. This will cause memcpy in copy_compressed_segment to write outside of allocated memory. This mostly results in stuck read syscall but sometimes when using btrfs send can get #GP kernel: general protection fault, probably for non-canonical address 0x841551d5c1000: 0000 [#1] PREEMPT SMP NOPTI kernel: CPU: 17 PID: 264 Comm: kworker/u256:7 Tainted: P OE 5.17.0-rc2-1 #12 kernel: Workqueue: btrfs-endio btrfs_work_helper [btrfs] kernel: RIP: 0010:lzo_decompress_bio (./include/linux/fortify-string.h:225 fs/btrfs/lzo.c:322 fs/btrfs/lzo.c:394) btrfs Code starting with the faulting instruction =========================================== 0:* 48 8b 06 mov (%rsi),%rax <-- trapping instruction 3: 48 8d 79 08 lea 0x8(%rcx),%rdi 7: 48 83 e7 f8 and $0xfffffffffffffff8,%rdi b: 48 89 01 mov %rax,(%rcx) e: 44 89 f0 mov %r14d,%eax 11: 48 8b 54 06 f8 mov -0x8(%rsi,%rax,1),%rdx kernel: RSP: 0018:ffffb110812efd50 EFLAGS: 00010212 kernel: RAX: 0000000000001000 RBX: 000000009ca264c8 RCX: ffff98996e6d8ff8 kernel: RDX: 0000000000000064 RSI: 000841551d5c1000 RDI: ffffffff9500435d kernel: RBP: ffff989a3be856c0 R08: 0000000000000000 R09: 0000000000000000 kernel: R10: 0000000000000000 R11: 0000000000001000 R12: ffff98996e6d8000 kernel: R13: 0000000000000008 R14: 0000000000001000 R15: 000841551d5c1000 kernel: FS: 0000000000000000(0000) GS:ffff98a09d640000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00001e9f984d9ea8 CR3: 000000014971a000 CR4: 00000000003506e0 kernel: Call Trace: kernel: <TASK> kernel: end_compressed_bio_read (fs/btrfs/compression.c:104 fs/btrfs/compression.c:1363 fs/btrfs/compression.c:323) btrfs kernel: end_workqueue_fn (fs/btrfs/disk-io.c:1923) btrfs kernel: btrfs_work_helper (fs/btrfs/async-thread.c:326) btrfs kernel: process_one_work (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:212 ./include/trace/events/workqueue.h:108 kernel/workqueue.c:2312) kernel: worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2455) kernel: ? process_one_work (kernel/workqueue.c:2397) kernel: kthread (kernel/kthread.c:377) kernel: ? kthread_complete_and_exit (kernel/kthread.c:332) kernel: ret_from_fork (arch/x86/entry/entry_64.S:301) kernel: </TASK> | ||||
| CVE-2022-48871 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on default RX FIFO depth, e.g. 16. Later during serial startup the qcom_geni_serial_port_setup() updates the RX FIFO depth (port->rx_fifo_depth) to match real device capabilities, e.g. to 32. The RX UART handle code will read "port->rx_fifo_depth" number of words into "port->rx_fifo" buffer, thus exceeding the bounds. This can be observed in certain configurations with Qualcomm Bluetooth HCI UART device and KASAN: Bluetooth: hci0: QCA Product ID :0x00000010 Bluetooth: hci0: QCA SOC Version :0x400a0200 Bluetooth: hci0: QCA ROM Version :0x00000200 Bluetooth: hci0: QCA Patch Version:0x00000d2b Bluetooth: hci0: QCA controller version 0x02000200 Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2 Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2) Bluetooth: hci0: QCA Failed to download patch (-2) ================================================================== BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c Write of size 4 at addr ffff279347d578c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26 Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) Call trace: dump_backtrace.part.0+0xe0/0xf0 show_stack+0x18/0x40 dump_stack_lvl+0x8c/0xb8 print_report+0x188/0x488 kasan_report+0xb4/0x100 __asan_store4+0x80/0xa4 handle_rx_uart+0xa8/0x18c qcom_geni_serial_handle_rx+0x84/0x9c qcom_geni_serial_isr+0x24c/0x760 __handle_irq_event_percpu+0x108/0x500 handle_irq_event+0x6c/0x110 handle_fasteoi_irq+0x138/0x2cc generic_handle_domain_irq+0x48/0x64 If the RX FIFO depth changes after probe, be sure to resize the buffer. | ||||
| CVE-2022-48847 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: watch_queue: Fix filter limit check In watch_queue_set_filter(), there are a couple of places where we check that the filter type value does not exceed what the type_filter bitmap can hold. One place calculates the number of bits by: if (tf[i].type >= sizeof(wfilter->type_filter) * 8) which is fine, but the second does: if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG) which is not. This can lead to a couple of out-of-bounds writes due to a too-large type: (1) __set_bit() on wfilter->type_filter (2) Writing more elements in wfilter->filters[] than we allocated. Fix this by just using the proper WATCH_TYPE__NR instead, which is the number of types we actually know about. The bug may cause an oops looking something like: BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740 Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611 ... Call Trace: <TASK> dump_stack_lvl+0x45/0x59 print_address_description.constprop.0+0x1f/0x150 ... kasan_report.cold+0x7f/0x11b ... watch_queue_set_filter+0x659/0x740 ... __x64_sys_ioctl+0x127/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Allocated by task 611: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 watch_queue_set_filter+0x23a/0x740 __x64_sys_ioctl+0x127/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae The buggy address belongs to the object at ffff88800d2c66a0 which belongs to the cache kmalloc-32 of size 32 The buggy address is located 28 bytes inside of 32-byte region [ffff88800d2c66a0, ffff88800d2c66c0) | ||||
| CVE-2022-48744 | 2024-12-19 | 6.7 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Avoid field-overflowing memcpy() In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Use flexible arrays instead of zero-element arrays (which look like they are always overflowing) and split the cross-field memcpy() into two halves that can be appropriately bounds-checked by the compiler. We were doing: #define ETH_HLEN 14 #define VLAN_HLEN 4 ... #define MLX5E_XDP_MIN_INLINE (ETH_HLEN + VLAN_HLEN) ... struct mlx5e_tx_wqe *wqe = mlx5_wq_cyc_get_wqe(wq, pi); ... struct mlx5_wqe_eth_seg *eseg = &wqe->eth; struct mlx5_wqe_data_seg *dseg = wqe->data; ... memcpy(eseg->inline_hdr.start, xdptxd->data, MLX5E_XDP_MIN_INLINE); target is wqe->eth.inline_hdr.start (which the compiler sees as being 2 bytes in size), but copying 18, intending to write across start (really vlan_tci, 2 bytes). The remaining 16 bytes get written into wqe->data[0], covering byte_count (4 bytes), lkey (4 bytes), and addr (8 bytes). struct mlx5e_tx_wqe { struct mlx5_wqe_ctrl_seg ctrl; /* 0 16 */ struct mlx5_wqe_eth_seg eth; /* 16 16 */ struct mlx5_wqe_data_seg data[]; /* 32 0 */ /* size: 32, cachelines: 1, members: 3 */ /* last cacheline: 32 bytes */ }; struct mlx5_wqe_eth_seg { u8 swp_outer_l4_offset; /* 0 1 */ u8 swp_outer_l3_offset; /* 1 1 */ u8 swp_inner_l4_offset; /* 2 1 */ u8 swp_inner_l3_offset; /* 3 1 */ u8 cs_flags; /* 4 1 */ u8 swp_flags; /* 5 1 */ __be16 mss; /* 6 2 */ __be32 flow_table_metadata; /* 8 4 */ union { struct { __be16 sz; /* 12 2 */ u8 start[2]; /* 14 2 */ } inline_hdr; /* 12 4 */ struct { __be16 type; /* 12 2 */ __be16 vlan_tci; /* 14 2 */ } insert; /* 12 4 */ __be32 trailer; /* 12 4 */ }; /* 12 4 */ /* size: 16, cachelines: 1, members: 9 */ /* last cacheline: 16 bytes */ }; struct mlx5_wqe_data_seg { __be32 byte_count; /* 0 4 */ __be32 lkey; /* 4 4 */ __be64 addr; /* 8 8 */ /* size: 16, cachelines: 1, members: 3 */ /* last cacheline: 16 bytes */ }; So, split the memcpy() so the compiler can reason about the buffer sizes. "pahole" shows no size nor member offset changes to struct mlx5e_tx_wqe nor struct mlx5e_umr_wqe. "objdump -d" shows no meaningful object code changes (i.e. only source line number induced differences and optimizations). | ||||
| CVE-2022-48743 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2024-12-19 | 5.3 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: amd-xgbe: Fix skb data length underflow There will be BUG_ON() triggered in include/linux/skbuff.h leading to intermittent kernel panic, when the skb length underflow is detected. Fix this by dropping the packet if such length underflows are seen because of inconsistencies in the hardware descriptors. | ||||
| CVE-2021-47609 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scpi: Fix string overflow in SCPI genpd driver Without the bound checks for scpi_pd->name, it could result in the buffer overflow when copying the SCPI device name from the corresponding device tree node as the name string is set at maximum size of 30. Let us fix it by using devm_kasprintf so that the string buffer is allocated dynamically. | ||||
| CVE-2021-47605 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: vduse: fix memory corruption in vduse_dev_ioctl() The "config.offset" comes from the user. There needs to a check to prevent it being out of bounds. The "config.offset" and "dev->config_size" variables are both type u32. So if the offset if out of bounds then the "dev->config_size - config.offset" subtraction results in a very high u32 value. The out of bounds offset can result in memory corruption. | ||||
| CVE-2021-47595 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_ets: don't remove idle classes from the round-robin list Shuang reported that the following script: 1) tc qdisc add dev ddd0 handle 10: parent 1: ets bands 8 strict 4 priomap 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 2) mausezahn ddd0 -A 10.10.10.1 -B 10.10.10.2 -c 0 -a own -b 00:c1:a0:c1:a0:00 -t udp & 3) tc qdisc change dev ddd0 handle 10: ets bands 4 strict 2 quanta 2500 2500 priomap 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 crashes systematically when line 2) is commented: list_del corruption, ffff8e028404bd30->next is LIST_POISON1 (dead000000000100) ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:47! invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 954 Comm: tc Not tainted 5.16.0-rc4+ #478 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014 RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x47 Code: fe ff 0f 0b 48 89 c1 4c 89 c6 48 c7 c7 08 42 1b 87 e8 1d c5 fe ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 98 42 1b 87 e8 09 c5 fe ff <0f> 0b 48 c7 c7 48 43 1b 87 e8 fb c4 fe ff 0f 0b 48 89 f2 48 89 fe RSP: 0018:ffffae46807a3888 EFLAGS: 00010246 RAX: 000000000000004e RBX: 0000000000000007 RCX: 0000000000000202 RDX: 0000000000000000 RSI: ffffffff871ac536 RDI: 00000000ffffffff RBP: ffffae46807a3a10 R08: 0000000000000000 R09: c0000000ffff7fff R10: 0000000000000001 R11: ffffae46807a36a8 R12: ffff8e028404b800 R13: ffff8e028404bd30 R14: dead000000000100 R15: ffff8e02fafa2400 FS: 00007efdc92e4480(0000) GS:ffff8e02fb600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000682f48 CR3: 00000001058be000 CR4: 0000000000350ef0 Call Trace: <TASK> ets_qdisc_change+0x58b/0xa70 [sch_ets] tc_modify_qdisc+0x323/0x880 rtnetlink_rcv_msg+0x169/0x4a0 netlink_rcv_skb+0x50/0x100 netlink_unicast+0x1a5/0x280 netlink_sendmsg+0x257/0x4d0 sock_sendmsg+0x5b/0x60 ____sys_sendmsg+0x1f2/0x260 ___sys_sendmsg+0x7c/0xc0 __sys_sendmsg+0x57/0xa0 do_syscall_64+0x3a/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7efdc8031338 Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55 RSP: 002b:00007ffdf1ce9828 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000061b37a97 RCX: 00007efdc8031338 RDX: 0000000000000000 RSI: 00007ffdf1ce9890 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000078a940 R10: 000000000000000c R11: 0000000000000246 R12: 0000000000000001 R13: 0000000000688880 R14: 0000000000000000 R15: 0000000000000000 </TASK> Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt iTCO_vendor_support intel_rapl_msr intel_rapl_common joydev pcspkr i2c_i801 virtio_balloon i2c_smbus lpc_ich ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel serio_raw ghash_clmulni_intel ahci libahci libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod [last unloaded: sch_ets] ---[ end trace f35878d1912655c2 ]--- RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x47 Code: fe ff 0f 0b 48 89 c1 4c 89 c6 48 c7 c7 08 42 1b 87 e8 1d c5 fe ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 98 42 1b 87 e8 09 c5 fe ff <0f> 0b 48 c7 c7 48 43 1b 87 e8 fb c4 fe ff 0f 0b 48 89 f2 48 89 fe RSP: 0018:ffffae46807a3888 EFLAGS: 00010246 RAX: 000000000000004e RBX: 0000000000000007 RCX: 0000000000000202 RDX: 0000000000000000 RSI: ffffffff871ac536 RDI: 00000000ffffffff RBP: ffffae46807a3a10 R08: 0000000000000000 R09: c0000000ffff7fff R10: 0000000000000001 R11: ffffae46807a36a8 R12: ffff8e028404b800 R13: ffff8e028404bd30 R14: dead000000000100 R15: ffff8e02fafa2400 FS: 00007efdc92e4480(0000) GS:ffff8e02fb600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000 ---truncated--- | ||||
| CVE-2021-47547 | 2024-12-19 | 4.4 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: net: tulip: de4x5: fix the problem that the array 'lp->phy[8]' may be out of bound In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the 'for' end, the 'k' is 8. At this time, the array 'lp->phy[8]' may be out of bound. | ||||
| CVE-2021-47535 | 2024-12-19 | 6.2 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: drm/msm/a6xx: Allocate enough space for GMU registers In commit 142639a52a01 ("drm/msm/a6xx: fix crashstate capture for A650") we changed a6xx_get_gmu_registers() to read 3 sets of registers. Unfortunately, we didn't change the memory allocation for the array. That leads to a KASAN warning (this was on the chromeos-5.4 kernel, which has the problematic commit backported to it): BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430 Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209 CPU: 5 PID: 209 Comm: A618-worker Tainted: G W 5.4.156-lockdep #22 Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT) Call trace: dump_backtrace+0x0/0x248 show_stack+0x20/0x2c dump_stack+0x128/0x1ec print_address_description+0x88/0x4a0 __kasan_report+0xfc/0x120 kasan_report+0x10/0x18 __asan_report_store8_noabort+0x1c/0x24 _a6xx_get_gmu_registers+0x144/0x430 a6xx_gpu_state_get+0x330/0x25d4 msm_gpu_crashstate_capture+0xa0/0x84c recover_worker+0x328/0x838 kthread_worker_fn+0x32c/0x574 kthread+0x2dc/0x39c ret_from_fork+0x10/0x18 Allocated by task 209: __kasan_kmalloc+0xfc/0x1c4 kasan_kmalloc+0xc/0x14 kmem_cache_alloc_trace+0x1f0/0x2a0 a6xx_gpu_state_get+0x164/0x25d4 msm_gpu_crashstate_capture+0xa0/0x84c recover_worker+0x328/0x838 kthread_worker_fn+0x32c/0x574 kthread+0x2dc/0x39c ret_from_fork+0x10/0x18 | ||||