Filtered by vendor Redhat
Subscriptions
Total
21758 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2023-52455 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: iommu: Don't reserve 0-length IOVA region When the bootloader/firmware doesn't setup the framebuffers, their address and size are 0 in "iommu-addresses" property. If IOVA region is reserved with 0 length, then it ends up corrupting the IOVA rbtree with an entry which has pfn_hi < pfn_lo. If we intend to use display driver in kernel without framebuffer then it's causing the display IOMMU mappings to fail as entire valid IOVA space is reserved when address and length are passed as 0. An ideal solution would be firmware removing the "iommu-addresses" property and corresponding "memory-region" if display is not present. But the kernel should be able to handle this by checking for size of IOVA region and skipping the IOVA reservation if size is 0. Also, add a warning if firmware is requesting 0-length IOVA region reservation. | ||||
| CVE-2023-52451 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries/memhp: Fix access beyond end of drmem array dlpar_memory_remove_by_index() may access beyond the bounds of the drmem lmb array when the LMB lookup fails to match an entry with the given DRC index. When the search fails, the cursor is left pointing to &drmem_info->lmbs[drmem_info->n_lmbs], which is one element past the last valid entry in the array. The debug message at the end of the function then dereferences this pointer: pr_debug("Failed to hot-remove memory at %llx\n", lmb->base_addr); This was found by inspection and confirmed with KASAN: pseries-hotplug-mem: Attempting to hot-remove LMB, drc index 1234 ================================================================== BUG: KASAN: slab-out-of-bounds in dlpar_memory+0x298/0x1658 Read of size 8 at addr c000000364e97fd0 by task bash/949 dump_stack_lvl+0xa4/0xfc (unreliable) print_report+0x214/0x63c kasan_report+0x140/0x2e0 __asan_load8+0xa8/0xe0 dlpar_memory+0x298/0x1658 handle_dlpar_errorlog+0x130/0x1d0 dlpar_store+0x18c/0x3e0 kobj_attr_store+0x68/0xa0 sysfs_kf_write+0xc4/0x110 kernfs_fop_write_iter+0x26c/0x390 vfs_write+0x2d4/0x4e0 ksys_write+0xac/0x1a0 system_call_exception+0x268/0x530 system_call_vectored_common+0x15c/0x2ec Allocated by task 1: kasan_save_stack+0x48/0x80 kasan_set_track+0x34/0x50 kasan_save_alloc_info+0x34/0x50 __kasan_kmalloc+0xd0/0x120 __kmalloc+0x8c/0x320 kmalloc_array.constprop.0+0x48/0x5c drmem_init+0x2a0/0x41c do_one_initcall+0xe0/0x5c0 kernel_init_freeable+0x4ec/0x5a0 kernel_init+0x30/0x1e0 ret_from_kernel_user_thread+0x14/0x1c The buggy address belongs to the object at c000000364e80000 which belongs to the cache kmalloc-128k of size 131072 The buggy address is located 0 bytes to the right of allocated 98256-byte region [c000000364e80000, c000000364e97fd0) ================================================================== pseries-hotplug-mem: Failed to hot-remove memory at 0 Log failed lookups with a separate message and dereference the cursor only when it points to a valid entry. | ||||
| CVE-2023-52450 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel/uncore: Fix NULL pointer dereference issue in upi_fill_topology() Get logical socket id instead of physical id in discover_upi_topology() to avoid out-of-bound access on 'upi = &type->topology[nid][idx];' line that leads to NULL pointer dereference in upi_fill_topology() | ||||
| CVE-2023-52448 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix kernel NULL pointer dereference in gfs2_rgrp_dump Syzkaller has reported a NULL pointer dereference when accessing rgd->rd_rgl in gfs2_rgrp_dump(). This can happen when creating rgd->rd_gl fails in read_rindex_entry(). Add a NULL pointer check in gfs2_rgrp_dump() to prevent that. | ||||
| CVE-2023-52445 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: media: pvrusb2: fix use after free on context disconnection Upon module load, a kthread is created targeting the pvr2_context_thread_func function, which may call pvr2_context_destroy and thus call kfree() on the context object. However, that might happen before the usb hub_event handler is able to notify the driver. This patch adds a sanity check before the invalid read reported by syzbot, within the context disconnection call stack. | ||||
| CVE-2022-49028 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ixgbevf: Fix resource leak in ixgbevf_init_module() ixgbevf_init_module() won't destroy the workqueue created by create_singlethread_workqueue() when pci_register_driver() failed. Add destroy_workqueue() in fail path to prevent the resource leak. Similar to the handling of u132_hcd_init in commit f276e002793c ("usb: u132-hcd: fix resource leak") | ||||
| CVE-2022-49011 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: (coretemp) fix pci device refcount leak in nv1a_ram_new() As comment of pci_get_domain_bus_and_slot() says, it returns a pci device with refcount increment, when finish using it, the caller must decrement the reference count by calling pci_dev_put(). So call it after using to avoid refcount leak. | ||||
| CVE-2022-49010 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: (coretemp) Check for null before removing sysfs attrs If coretemp_add_core() gets an error then pdata->core_data[indx] is already NULL and has been kfreed. Don't pass that to sysfs_remove_group() as that will crash in sysfs_remove_group(). [Shortened for readability] [91854.020159] sysfs: cannot create duplicate filename '/devices/platform/coretemp.0/hwmon/hwmon2/temp20_label' <cpu offline> [91855.126115] BUG: kernel NULL pointer dereference, address: 0000000000000188 [91855.165103] #PF: supervisor read access in kernel mode [91855.194506] #PF: error_code(0x0000) - not-present page [91855.224445] PGD 0 P4D 0 [91855.238508] Oops: 0000 [#1] PREEMPT SMP PTI ... [91855.342716] RIP: 0010:sysfs_remove_group+0xc/0x80 ... [91855.796571] Call Trace: [91855.810524] coretemp_cpu_offline+0x12b/0x1dd [coretemp] [91855.841738] ? coretemp_cpu_online+0x180/0x180 [coretemp] [91855.871107] cpuhp_invoke_callback+0x105/0x4b0 [91855.893432] cpuhp_thread_fun+0x8e/0x150 ... Fix this by checking for NULL first. | ||||
| CVE-2022-48997 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: char: tpm: Protect tpm_pm_suspend with locks Currently tpm transactions are executed unconditionally in tpm_pm_suspend() function, which may lead to races with other tpm accessors in the system. Specifically, the hw_random tpm driver makes use of tpm_get_random(), and this function is called in a loop from a kthread, which means it's not frozen alongside userspace, and so can race with the work done during system suspend: tpm tpm0: tpm_transmit: tpm_recv: error -52 tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics CPU: 0 PID: 1 Comm: init Not tainted 6.1.0-rc5+ #135 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014 Call Trace: tpm_tis_status.cold+0x19/0x20 tpm_transmit+0x13b/0x390 tpm_transmit_cmd+0x20/0x80 tpm1_pm_suspend+0xa6/0x110 tpm_pm_suspend+0x53/0x80 __pnp_bus_suspend+0x35/0xe0 __device_suspend+0x10f/0x350 Fix this by calling tpm_try_get_ops(), which itself is a wrapper around tpm_chip_start(), but takes the appropriate mutex. [Jason: reworked commit message, added metadata] | ||||
| CVE-2022-48992 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: soc-pcm: Add NULL check in BE reparenting Add NULL check in dpcm_be_reparent API, to handle kernel NULL pointer dereference error. The issue occurred in fuzzing test. | ||||
| CVE-2022-48988 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: memcg: fix possible use-after-free in memcg_write_event_control() memcg_write_event_control() accesses the dentry->d_name of the specified control fd to route the write call. As a cgroup interface file can't be renamed, it's safe to access d_name as long as the specified file is a regular cgroup file. Also, as these cgroup interface files can't be removed before the directory, it's safe to access the parent too. Prior to 347c4a874710 ("memcg: remove cgroup_event->cft"), there was a call to __file_cft() which verified that the specified file is a regular cgroupfs file before further accesses. The cftype pointer returned from __file_cft() was no longer necessary and the commit inadvertently dropped the file type check with it allowing any file to slip through. With the invarients broken, the d_name and parent accesses can now race against renames and removals of arbitrary files and cause use-after-free's. Fix the bug by resurrecting the file type check in __file_cft(). Now that cgroupfs is implemented through kernfs, checking the file operations needs to go through a layer of indirection. Instead, let's check the superblock and dentry type. | ||||
| CVE-2022-48976 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: flowtable_offload: fix using __this_cpu_add in preemptible flow_offload_queue_work() can be called in workqueue without bh disabled, like the call trace showed in my act_ct testing, calling NF_FLOW_TABLE_STAT_INC() there would cause a call trace: BUG: using __this_cpu_add() in preemptible [00000000] code: kworker/u4:0/138560 caller is flow_offload_queue_work+0xec/0x1b0 [nf_flow_table] Workqueue: act_ct_workqueue tcf_ct_flow_table_cleanup_work [act_ct] Call Trace: <TASK> dump_stack_lvl+0x33/0x46 check_preemption_disabled+0xc3/0xf0 flow_offload_queue_work+0xec/0x1b0 [nf_flow_table] nf_flow_table_iterate+0x138/0x170 [nf_flow_table] nf_flow_table_free+0x140/0x1a0 [nf_flow_table] tcf_ct_flow_table_cleanup_work+0x2f/0x2b0 [act_ct] process_one_work+0x6a3/0x1030 worker_thread+0x8a/0xdf0 This patch fixes it by using NF_FLOW_TABLE_STAT_INC_ATOMIC() instead in flow_offload_queue_work(). Note that for FLOW_CLS_REPLACE branch in flow_offload_queue_work(), it may not be called in preemptible path, but it's good to use NF_FLOW_TABLE_STAT_INC_ATOMIC() for all cases in flow_offload_queue_work(). | ||||
| CVE-2022-48974 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: conntrack: fix using __this_cpu_add in preemptible Currently in nf_conntrack_hash_check_insert(), when it fails in nf_ct_ext_valid_pre/post(), NF_CT_STAT_INC() will be called in the preemptible context, a call trace can be triggered: BUG: using __this_cpu_add() in preemptible [00000000] code: conntrack/1636 caller is nf_conntrack_hash_check_insert+0x45/0x430 [nf_conntrack] Call Trace: <TASK> dump_stack_lvl+0x33/0x46 check_preemption_disabled+0xc3/0xf0 nf_conntrack_hash_check_insert+0x45/0x430 [nf_conntrack] ctnetlink_create_conntrack+0x3cd/0x4e0 [nf_conntrack_netlink] ctnetlink_new_conntrack+0x1c0/0x450 [nf_conntrack_netlink] nfnetlink_rcv_msg+0x277/0x2f0 [nfnetlink] netlink_rcv_skb+0x50/0x100 nfnetlink_rcv+0x65/0x144 [nfnetlink] netlink_unicast+0x1ae/0x290 netlink_sendmsg+0x257/0x4f0 sock_sendmsg+0x5f/0x70 This patch is to fix it by changing to use NF_CT_STAT_INC_ATOMIC() for nf_ct_ext_valid_pre/post() check in nf_conntrack_hash_check_insert(), as well as nf_ct_ext_valid_post() in __nf_conntrack_confirm(). Note that nf_ct_ext_valid_pre() check in __nf_conntrack_confirm() is safe to use NF_CT_STAT_INC(), as it's under local_bh_disable(). | ||||
| CVE-2022-48947 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix u8 overflow By keep sending L2CAP_CONF_REQ packets, chan->num_conf_rsp increases multiple times and eventually it will wrap around the maximum number (i.e., 255). This patch prevents this by adding a boundary check with L2CAP_MAX_CONF_RSP Btmon log: Bluetooth monitor ver 5.64 = Note: Linux version 6.1.0-rc2 (x86_64) 0.264594 = Note: Bluetooth subsystem version 2.22 0.264636 @ MGMT Open: btmon (privileged) version 1.22 {0x0001} 0.272191 = New Index: 00:00:00:00:00:00 (Primary,Virtual,hci0) [hci0] 13.877604 @ RAW Open: 9496 (privileged) version 2.22 {0x0002} 13.890741 = Open Index: 00:00:00:00:00:00 [hci0] 13.900426 (...) > ACL Data RX: Handle 200 flags 0x00 dlen 1033 #32 [hci0] 14.273106 invalid packet size (12 != 1033) 08 00 01 00 02 01 04 00 01 10 ff ff ............ > ACL Data RX: Handle 200 flags 0x00 dlen 1547 #33 [hci0] 14.273561 invalid packet size (14 != 1547) 0a 00 01 00 04 01 06 00 40 00 00 00 00 00 ........@..... > ACL Data RX: Handle 200 flags 0x00 dlen 2061 #34 [hci0] 14.274390 invalid packet size (16 != 2061) 0c 00 01 00 04 01 08 00 40 00 00 00 00 00 00 04 ........@....... > ACL Data RX: Handle 200 flags 0x00 dlen 2061 #35 [hci0] 14.274932 invalid packet size (16 != 2061) 0c 00 01 00 04 01 08 00 40 00 00 00 07 00 03 00 ........@....... = bluetoothd: Bluetooth daemon 5.43 14.401828 > ACL Data RX: Handle 200 flags 0x00 dlen 1033 #36 [hci0] 14.275753 invalid packet size (12 != 1033) 08 00 01 00 04 01 04 00 40 00 00 00 ........@... | ||||
| CVE-2022-48943 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhev Hypervisor | 2024-12-19 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: KVM: x86/mmu: make apf token non-zero to fix bug In current async pagefault logic, when a page is ready, KVM relies on kvm_arch_can_dequeue_async_page_present() to determine whether to deliver a READY event to the Guest. This function test token value of struct kvm_vcpu_pv_apf_data, which must be reset to zero by Guest kernel when a READY event is finished by Guest. If value is zero meaning that a READY event is done, so the KVM can deliver another. But the kvm_arch_setup_async_pf() may produce a valid token with zero value, which is confused with previous mention and may lead the loss of this READY event. This bug may cause task blocked forever in Guest: INFO: task stress:7532 blocked for more than 1254 seconds. Not tainted 5.10.0 #16 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:stress state:D stack: 0 pid: 7532 ppid: 1409 flags:0x00000080 Call Trace: __schedule+0x1e7/0x650 schedule+0x46/0xb0 kvm_async_pf_task_wait_schedule+0xad/0xe0 ? exit_to_user_mode_prepare+0x60/0x70 __kvm_handle_async_pf+0x4f/0xb0 ? asm_exc_page_fault+0x8/0x30 exc_page_fault+0x6f/0x110 ? asm_exc_page_fault+0x8/0x30 asm_exc_page_fault+0x1e/0x30 RIP: 0033:0x402d00 RSP: 002b:00007ffd31912500 EFLAGS: 00010206 RAX: 0000000000071000 RBX: ffffffffffffffff RCX: 00000000021a32b0 RDX: 000000000007d011 RSI: 000000000007d000 RDI: 00000000021262b0 RBP: 00000000021262b0 R08: 0000000000000003 R09: 0000000000000086 R10: 00000000000000eb R11: 00007fefbdf2baa0 R12: 0000000000000000 R13: 0000000000000002 R14: 000000000007d000 R15: 0000000000001000 | ||||
| CVE-2022-48942 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: Handle failure to register sensor with thermal zone correctly If an attempt is made to a sensor with a thermal zone and it fails, the call to devm_thermal_zone_of_sensor_register() may return -ENODEV. This may result in crashes similar to the following. Unable to handle kernel NULL pointer dereference at virtual address 00000000000003cd ... Internal error: Oops: 96000021 [#1] PREEMPT SMP ... pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : mutex_lock+0x18/0x60 lr : thermal_zone_device_update+0x40/0x2e0 sp : ffff800014c4fc60 x29: ffff800014c4fc60 x28: ffff365ee3f6e000 x27: ffffdde218426790 x26: ffff365ee3f6e000 x25: 0000000000000000 x24: ffff365ee3f6e000 x23: ffffdde218426870 x22: ffff365ee3f6e000 x21: 00000000000003cd x20: ffff365ee8bf3308 x19: ffffffffffffffed x18: 0000000000000000 x17: ffffdde21842689c x16: ffffdde1cb7a0b7c x15: 0000000000000040 x14: ffffdde21a4889a0 x13: 0000000000000228 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : 0000000001120000 x7 : 0000000000000001 x6 : 0000000000000000 x5 : 0068000878e20f07 x4 : 0000000000000000 x3 : 00000000000003cd x2 : ffff365ee3f6e000 x1 : 0000000000000000 x0 : 00000000000003cd Call trace: mutex_lock+0x18/0x60 hwmon_notify_event+0xfc/0x110 0xffffdde1cb7a0a90 0xffffdde1cb7a0b7c irq_thread_fn+0x2c/0xa0 irq_thread+0x134/0x240 kthread+0x178/0x190 ret_from_fork+0x10/0x20 Code: d503201f d503201f d2800001 aa0103e4 (c8e47c02) Jon Hunter reports that the exact call sequence is: hwmon_notify_event() --> hwmon_thermal_notify() --> thermal_zone_device_update() --> update_temperature() --> mutex_lock() The hwmon core needs to handle all errors returned from calls to devm_thermal_zone_of_sensor_register(). If the call fails with -ENODEV, report that the sensor was not attached to a thermal zone but continue to register the hwmon device. | ||||
| CVE-2022-48939 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 3.3 Low |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Add schedule points in batch ops syzbot reported various soft lockups caused by bpf batch operations. INFO: task kworker/1:1:27 blocked for more than 140 seconds. INFO: task hung in rcu_barrier Nothing prevents batch ops to process huge amount of data, we need to add schedule points in them. Note that maybe_wait_bpf_programs(map) calls from generic_map_delete_batch() can be factorized by moving the call after the loop. This will be done later in -next tree once we get this fix merged, unless there is strong opinion doing this optimization sooner. | ||||
| CVE-2022-48934 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: nfp: flower: Fix a potential leak in nfp_tunnel_add_shared_mac() ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX) inclusive. So NFP_MAX_MAC_INDEX (0xff) is a valid id. In order for the error handling path to work correctly, the 'invalid' value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range, inclusive. So set it to -1. | ||||
| CVE-2022-48921 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: sched/fair: Fix fault in reweight_entity Syzbot found a GPF in reweight_entity. This has been bisected to commit 4ef0c5c6b5ba ("kernel/sched: Fix sched_fork() access an invalid sched_task_group") There is a race between sched_post_fork() and setpriority(PRIO_PGRP) within a thread group that causes a null-ptr-deref in reweight_entity() in CFS. The scenario is that the main process spawns number of new threads, which then call setpriority(PRIO_PGRP, 0, -20), wait, and exit. For each of the new threads the copy_process() gets invoked, which adds the new task_struct and calls sched_post_fork() for it. In the above scenario there is a possibility that setpriority(PRIO_PGRP) and set_one_prio() will be called for a thread in the group that is just being created by copy_process(), and for which the sched_post_fork() has not been executed yet. This will trigger a null pointer dereference in reweight_entity(), as it will try to access the run queue pointer, which hasn't been set. Before the mentioned change the cfs_rq pointer for the task has been set in sched_fork(), which is called much earlier in copy_process(), before the new task is added to the thread_group. Now it is done in the sched_post_fork(), which is called after that. To fix the issue the remove the update_load param from the update_load param() function and call reweight_task() only if the task flag doesn't have the TASK_NEW flag set. | ||||
| CVE-2022-48918 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: iwlwifi: mvm: check debugfs_dir ptr before use When "debugfs=off" is used on the kernel command line, iwiwifi's mvm module uses an invalid/unchecked debugfs_dir pointer and causes a BUG: BUG: kernel NULL pointer dereference, address: 000000000000004f #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP CPU: 1 PID: 503 Comm: modprobe Tainted: G W 5.17.0-rc5 #7 Hardware name: Dell Inc. Inspiron 15 5510/076F7Y, BIOS 2.4.1 11/05/2021 RIP: 0010:iwl_mvm_dbgfs_register+0x692/0x700 [iwlmvm] Code: 69 a0 be 80 01 00 00 48 c7 c7 50 73 6a a0 e8 95 cf ee e0 48 8b 83 b0 1e 00 00 48 c7 c2 54 73 6a a0 be 64 00 00 00 48 8d 7d 8c <48> 8b 48 50 e8 15 22 07 e1 48 8b 43 28 48 8d 55 8c 48 c7 c7 5f 73 RSP: 0018:ffffc90000a0ba68 EFLAGS: 00010246 RAX: ffffffffffffffff RBX: ffff88817d6e3328 RCX: ffff88817d6e3328 RDX: ffffffffa06a7354 RSI: 0000000000000064 RDI: ffffc90000a0ba6c RBP: ffffc90000a0bae0 R08: ffffffff824e4880 R09: ffffffffa069d620 R10: ffffc90000a0ba00 R11: ffffffffffffffff R12: 0000000000000000 R13: ffffc90000a0bb28 R14: ffff88817d6e3328 R15: ffff88817d6e3320 FS: 00007f64dd92d740(0000) GS:ffff88847f640000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000004f CR3: 000000016fc79001 CR4: 0000000000770ee0 PKRU: 55555554 Call Trace: <TASK> ? iwl_mvm_mac_setup_register+0xbdc/0xda0 [iwlmvm] iwl_mvm_start_post_nvm+0x71/0x100 [iwlmvm] iwl_op_mode_mvm_start+0xab8/0xb30 [iwlmvm] _iwl_op_mode_start+0x6f/0xd0 [iwlwifi] iwl_opmode_register+0x6a/0xe0 [iwlwifi] ? 0xffffffffa0231000 iwl_mvm_init+0x35/0x1000 [iwlmvm] ? 0xffffffffa0231000 do_one_initcall+0x5a/0x1b0 ? kmem_cache_alloc+0x1e5/0x2f0 ? do_init_module+0x1e/0x220 do_init_module+0x48/0x220 load_module+0x2602/0x2bc0 ? __kernel_read+0x145/0x2e0 ? kernel_read_file+0x229/0x290 __do_sys_finit_module+0xc5/0x130 ? __do_sys_finit_module+0xc5/0x130 __x64_sys_finit_module+0x13/0x20 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f64dda564dd Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1b 29 0f 00 f7 d8 64 89 01 48 RSP: 002b:00007ffdba393f88 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f64dda564dd RDX: 0000000000000000 RSI: 00005575399e2ab2 RDI: 0000000000000001 RBP: 000055753a91c5e0 R08: 0000000000000000 R09: 0000000000000002 R10: 0000000000000001 R11: 0000000000000246 R12: 00005575399e2ab2 R13: 000055753a91ceb0 R14: 0000000000000000 R15: 000055753a923018 </TASK> Modules linked in: btintel(+) btmtk bluetooth vfat snd_hda_codec_hdmi fat snd_hda_codec_realtek snd_hda_codec_generic iwlmvm(+) snd_sof_pci_intel_tgl mac80211 snd_sof_intel_hda_common soundwire_intel soundwire_generic_allocation soundwire_cadence soundwire_bus snd_sof_intel_hda snd_sof_pci snd_sof snd_sof_xtensa_dsp snd_soc_hdac_hda snd_hda_ext_core snd_soc_acpi_intel_match snd_soc_acpi snd_soc_core btrfs snd_compress snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec raid6_pq iwlwifi snd_hda_core snd_pcm snd_timer snd soundcore cfg80211 intel_ish_ipc(+) thunderbolt rfkill intel_ishtp ucsi_acpi wmi i2c_hid_acpi i2c_hid evdev CR2: 000000000000004f ---[ end trace 0000000000000000 ]--- Check the debugfs_dir pointer for an error before using it. [change to make both conditional] | ||||